HYUNDAI TERRACAN Front Shock Absorber
How to install the new shock absorber Position the rubber bushing on the piston rod and carefully push it down until it is seated well on the grommet. With the convex side down, slide the second grommet on the piston rod of the shock absorber. Make sure it sits well on the rubber bushing. If the...
How to install the new shock absorber
Position the rubber bushing on the piston rod and carefully push it down until it is seated well on the grommet. With the convex side down, slide the second grommet on the piston rod of the shock absorber. Make sure it sits well on the rubber bushing.
If the new front shock absorber comes with a plastic strip around the shock, you have to remove the plastic. This is usually placed by some manufacturers to prevent shock compression during shipping.
Install the new shock absorber between the upper and the lower suspension arms and push the piston rod through its holed slot in the upper suspension arm. Secure the piston rod by tightening the upper nut.
Compress the shock with slow and gradual pressure. Do not stop until the shock’s bottom is aligned with the mounting holes on the lower suspension arm.
Slide in the bolt at the lower mounting holes and screw in the nut onto the bolt.
Put back the wheel and tighten the lug nuts. Lower the vehicle and screw in all the lug nuts one quarter of a turn.
How to disconnect the shock from the suspension.
Use a socket set or a nut splitter to disengage the nut that connecting the shock to the suspension, and remove it from the bolt. If there isn't enough room to operate the splitter, you can apply penetrating solvent.
Depending on the assembly, you may also need to disengage the knuckle at the top of brake assembly to get the the shock. Consult your owner's manual to find out for sure. Use the same process to remove the nut that is positioned at the top and keep the nuts separate so you will know which one goes where when it is time to install your new shocks.
Our shock absorber adopts high-quality oil seal and steels,combining with compound-mouth oil seal technology,in order to give double protections to the shock absorber. Also,the shock absorber has applied the word advanced technology of chrome plating treatment to the micro-crack of hard chromed piston rod,combing with fine processing ,in order to highly improve quality of shock absorber and endure application performance and service life. Most important, the shock absorber also can control the car body rake forward due to inertia brake and side rolling due to car turning around in an effective way,thus to highly improve car driving and riding comfort and make cars suit various road condition
●Spring Type: Coil Spring
●Spring Material: Steel
●Shock Absorber Type: Gas-Filled
●Warranty: 1 year
●Material: Rubber, Steel
●Color: Black or as your request
●PAYMENT: T/T, Paypal, Western Union, etc.
1)All weather fluid
2) Hard chromed piston rod reduces friction
3) Seamless cylinder reduces possibility of splitting
4) High-Pressure Nitrogen Gas
5)Quality contral system certified by ISO/TS16949
SHOCK ABSORBER DETAILS
1, The weld: Use of robot welding, equipped with Matsushita automatic welding machine and 1.5MM wire, to ensure consistency 、aesthetics of welding, welding depth of 1.5mm, pull force ≥ 45KN.
2 Electrophoretic paint: Use of electrophoretic coating, film thickness 0.04-0.06, salt spray test ≥ 480 hours, the appearance of high finish, without any dead ends.
3, NOK oil seal: Use of Japan NOK oil seal, NOK oil seal is the industry's highest quality oil seal, the use of natural high-quality (NBR) production, effectively suppress the shock absorber oil leak, abnormal sound; tolerance temperature -45 ℃ -120 ℃ , Inflatable pressure reached 3MPa
4，Connecting rod: Degree of finish ≤ 0.05, chrome layer thickness ≥0.02, quenching depth 1-1.5, quenching hardness Rockwell HRC50-55; chrome layer Vickers hardness HV900-HV1300, piston end beating ≤ 0.03, micro-crack evenly distributed
Packaging & Delivery
Neutral Package: One piece in one bag, one piece in one carton box, 4-6 pieces in one carton, One 40'HQ container could load about 1200pcs.
Print Package: could be made and used by your own designed package.
Delivery Detail:45 days upon receipt of 30% deposit payment
Q1. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q2. What is your sample policy?
A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and
the courier cost.
Q3: How do you make our business long-term and good relationship?
A:1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.